鋁板在生產過程中往往會有很多問題，鋁板生產中為常見的問題不外乎表面問題、板型問題、軋制厚度問題。所以生產人員在鋁板生產中要時刻的關注以上幾個要點，下面鋁板生產廠家來講講吧。
There are often many problems in the production process of aluminum plates. The common problems in aluminum plate production are nothing more than surface problems, plate shape problems, and rolling thickness problems. Therefore, the production personnel should always pay attention to the above points in the aluminum plate production. Let's talk about it from the aluminum plate manufacturer.
鋁板生產中的表面問題：
Surface problems in aluminum plate production:
表面問題主要為擦劃傷、黃油斑問題，鋁板在生產過程中如果機臺上面有金屬顆粒那么會在生產過程中出現紋理一直的擦劃傷，生產人員需要立即停機清理機臺。黃油斑問題是由于軋制油沒有及時更換或者是軋制設備的吹風系統出現故障導致的，雖然后期可通過鋁板拉彎矯清洗進行處理，但是生產人員還是需要注意黃油斑，如果對于高要求的外觀件對于黃油斑都是視為不合格的鋁板。
The surface problems are mainly scratches and grease stains. If there are metal particles on the machine table during the production process, the aluminum plate will be scratched all the time during the production process. The production personnel need to stop the machine immediately to clean the machine table. The problem of grease stain is caused by the rolling oil not being replaced in time or the failure of the air blowing system of the rolling equipment. Although it can be handled through the aluminum plate stretching, bending, straightening and cleaning in the later stage, the production personnel still need to pay attention to the yellow oil stain. If the parts with high requirements for appearance are regarded as unqualified aluminum plates for the grease stain.
鋁板生產中的板型問題：
Plate type problems in aluminum plate production:
板型問題一直是比較難以控制的，主要和軋機軋輥有關系，軋機如果在長期軋制過程中沒有及時修復軋輥磨損的間隙則會出現板型波浪問題，中浪和邊浪都可能會產生。波浪板型問題已經發現生產人員需要立即向生產主任反饋，排除是否因?yàn)檐垯C(jī)壓力不均勻還是其它原因，如果是軋輥磨損嚴重需要更換軋輥。
The plate shape problem is always difficult to control, which is mainly related to the rolling mill roll. If the rolling mill fails to repair the gap of the roll wear in a timely manner during the long-term rolling process, the plate shape wave problem will occur, and the middle wave and side wave may occur. The problem of wavy plate shape has been found that the production personnel need to report it to the production director immediately to rule out whether it is due to uneven rolling mill pressure or other reasons. If the roll is seriously worn, it needs to be replaced.

鋁板生產中的厚度問題：
Thickness problem in aluminum plate production:
還是和軋機有關系，軋機壓力不均勻?qū)е拢壳败垯C(jī)都有在線測量設備，該問題已經不再經常出現。
It is still related to the rolling mill, which is caused by uneven rolling mill pressure. At present, the rolling mill has online measuring equipment, and this problem no longer occurs frequently.
鋁板硬度問題：
Hardness of aluminum plate:
主要和退火時間有關系，很多時候由于退火時間不足導致力學性能不達標，比如半硬狀態的鋁板出現折彎開裂，或者拉伸鋁板出現拉伸開裂均是鋁板硬度不達標，主要需要檢查退火設備的溫度、退火時間。
It is mainly related to the annealing time. In many cases, the mechanical properties are not up to the standard due to insufficient annealing time. For example, bending cracks occur on semi hard aluminum plates, or tensile cracks occur on stretched aluminum plates. The hardness of aluminum plates is not up to the standard. It is mainly necessary to check the temperature and annealing time of the annealing equipment.
生產車間的人員需要在生產中及時發現問題，同時及時糾正問題，避免鋁板出現質量不合格，提高鋁板的成品率和良品率。更多相關事項就來我們網站http://m.baihuiplaza.com進行咨詢吧！
The personnel in the production workshop need to find problems in time during production and correct them in time to avoid unqualified aluminum plates and improve the yield and yield of aluminum plates. Come to our website for more information http://m.baihuiplaza.com Consult!